Minimum tank size
Idaho is selected. Choose your bedrooms and press Calculate.
Drain field suitability in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties
Most rated land in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties is very limited for a standard drain field: 88% of it. Expect a site evaluation to point many lots toward a larger field, pressure distribution or an engineered system.
- 2% not limited
- 9% somewhat limited
- 87% very limited
- 1% not rated (urban land, water, pits)
Share of the soil survey area's 1,689,888 acres, by the USDA rating “ENG – Septic Tank Absorption Fields”. Ratings assume a standard gravity trench system with no site changes, so “very limited” means a conventional field needs special design, not that septic is impossible.
What limits drain fields here
The most common limiting factors in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties, as a share of all its land. One soil can have several, so the figures overlap.
Steep slopes64% of the county
Slopes over about 8% make it hard to keep trenches level and can let effluent seep out downhill.
Trenches are laid along the contour, often with serial distribution or drip dispersal.
Slow-draining subsoil48% of the county
Water moves too slowly through the soil 2 to 6 feet down, so effluent can back up or surface.
Designers usually answer with a larger drain field, shallower trenches, pressure dosing or a mound.
Drains too fast27% of the county
Coarse soil at the bottom of the trench passes effluent through before it is treated, which risks groundwater.
Pretreatment units or a sand liner slow the flow and finish the treatment.
Large stones22% of the county
Stones over 3 inches make up a quarter or more of the top 16 inches, which makes trenches hard to dig and level.
Contractors may need heavier equipment or imported fill.
Poor filtering layer19% of the county
Very permeable material 2 to 5 feet down filters effluent poorly.
Pretreatment or added fill gives the effluent more treatment before it reaches that layer.
Main soils in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties
The soils and land types covering the most ground. Search your address in the USDA Web Soil Survey to see which one is on your lot.
| Soil or land type | Share of county |
|---|---|
| Dawtonia | 4.3% |
| Zeebar | 3.4% |
| Dacont | 3.3% |
| Pahsimeroi | 2.6% |
| Zer | 2.4% |
| Cronks | 2.3% |
| Simeroi | 2.2% |
| Millhi | 2.0% |
Idaho tank size rules
Homes with 1 or 2 bedrooms need 900 gallons and 3 or 4 bedrooms need 1,000. Add 250 gallons for each bedroom over 4.
| Bedrooms | Minimum tank |
|---|---|
| 1 BR | 900 gal |
| 2 BR | 900 gal |
| 3 BR | 1,000 gal |
| 4 BR | 1,000 gal |
| 5 BR | 1,250 gal |
| 6 BR | 1,500 gal |
Source: IDAPA 58.01.03.007.07.
Common questions
Can I put a conventional septic system in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties?
Often, but not everywhere. The USDA rates 12% of rated land here as not or only somewhat limited for a standard drain field and 88% as very limited. Only a site evaluation on your lot can say which you have.
What size septic tank do I need in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties?
Idaho's minimum is 1,000 gal for 3 bedrooms and 1,000 gal for 4. Your county can require more.
What is the most common septic problem with soil in Custer-Lemhi Area, Parts of Blaine, Custer, and Lemhi Counties?
Steep slopes, a limiting factor on about 64% of the county. Trenches are laid along the contour, often with serial distribution or drip dispersal.
More in Idaho
Sources
- https://sdmdataaccess.sc.egov.usda.gov/
- https://websoilsurvey.nrcs.usda.gov/app/
- https://www.nrcs.usda.gov/resources/data-and-reports/soil-survey-interpretations
- https://www.epa.gov/septic/types-septic-systems
- https://d1tvxue8o4w0fl.cloudfront.net/regulation/idaho-administrative-code/title-idapa-58-environmental-quality-department-of/rule-580103-individualsubsurface-sewage-disposal-rules-and-rules-for-cleaning-of-septic-tanks/section-580103007-septic-tanks-design-and-construction-standards
- https://pubs.nmsu.edu/_m/M113/