Septic Tank Calculator

Home / Tools

Septic Soil Lookup by Address

Enter a property address or coordinates. We find the spot, look up the USDA soil survey for it and show how the soil is rated for a septic drain field.

Street, city, state and ZIP. We do not store addresses.
No street address? Use coordinates

Soil at this location

Enter an address and press Check my soil.

How the lookup works

  1. The U.S. Census Bureau's geocoder turns the address into latitude and longitude.
  2. The USDA Soil Data Access service finds the soil map unit at that point.
  3. We read the USDA rating “ENG – Septic Tank Absorption Fields” for each soil in the map unit, with the features that limit it.

A map unit often holds more than one soil, so the result lists each with its share. The rating assumes a standard gravity trench drain field with no site changes.

What the ratings mean

  • Not limited: the soil suits a standard drain field; ordinary design and installation work.
  • Somewhat limited: a standard field can work with careful design or installation.
  • Very limited: one or more features need special design, a larger field or an alternative system. It does not mean septic is impossible.
  • Not rated: urban land, water, pits and similar areas the survey does not rate.

The next step is a site evaluation or perc test on the lot, which costs $750 to $1,900 on average (Angi). More on perc tests.

Limiting features and what they mean

FeatureWhat it meansUsual answer
Slow-draining subsoilWater moves too slowly through the soil 2 to 6 feet down, so effluent can back up or surface.Designers usually answer with a larger drain field, shallower trenches, pressure dosing or a mound.
Steep slopesSlopes over about 8% make it hard to keep trenches level and can let effluent seep out downhill.Trenches are laid along the contour, often with serial distribution or drip dispersal.
High water tableThe water table rises to within 4 to 6 feet of the surface for part of the year, leaving too little dry soil to treat effluent.Mounds, sand filters or treatment units that need less separation are common answers.
Shallow bedrockRock lies within about 3 to 6 feet of the surface, so there is little soil to filter effluent before it reaches the rock.At-grade systems, mounds or drip dispersal add soil depth above the rock.
Drains too fastCoarse soil at the bottom of the trench passes effluent through before it is treated, which risks groundwater.Pretreatment units or a sand liner slow the flow and finish the treatment.
Flood-prone groundThe soil is on ground that floods, even if rarely, and a flooded drain field stops working.Systems are placed above flood level, with watertight tanks and backflow protection.
Poor filtering layerVery permeable material 2 to 5 feet down filters effluent poorly.Pretreatment or added fill gives the effluent more treatment before it reaches that layer.
PondingWater stands on the surface for hours after rain, which saturates the drain field.Sites are often raised with a mound or moved to higher ground on the lot.
Large stonesStones over 3 inches make up a quarter or more of the top 16 inches, which makes trenches hard to dig and level.Contractors may need heavier equipment or imported fill.
PermafrostPermanently frozen ground blocks drainage and can shift as it thaws.Systems are insulated, raised or replaced with holding tanks.
Settling organic soilOrganic soils can settle more than 2 feet, which breaks pipes and tilts tanks.Organic material is usually removed and replaced with engineered fill.
Hardpan or calicheA cemented layer within about 3 to 6 feet blocks downward drainage.Trenches may be dug through the pan, or a mound placed above it.
Unstable fillPlaced fill can settle unevenly and may not treat effluent well.A site evaluation decides whether the fill can be used.

Common questions

How accurate is a soil lookup by address?

It shows the soil the USDA mapped at that point. Soil maps cannot show every small patch, geocoded points can fall a little off the lot, and grading or fill changes the soil. Treat it as a first screen before a site evaluation.

Why was my address not found?

The Census geocoder covers most city and suburban addresses but misses many rural routes and new roads. Use “No street address? Use coordinates” and enter the lot's latitude and longitude, or stand on the land and use your phone's location.

Can I install septic if my soil is very limited?

Often, yes, with a mound, drip, sand filter or aerobic system, at a higher cost. Some sites cannot be permitted at all; your health department decides after a site evaluation.

Sources

  • https://sdmdataaccess.sc.egov.usda.gov/
  • https://geocoding.geo.census.gov/geocoder/
  • https://www.nrcs.usda.gov/resources/data-and-reports/soil-survey-interpretations
  • https://websoilsurvey.nrcs.usda.gov/app/
  • https://www.epa.gov/septic/types-septic-systems
  • https://www.angi.com/articles/perc-test-cost.htm